Wheel Spacer Adapters 15 mm 5×114.3 To 5×120 Conversion Hub Centric 2 PCS. At Caold Technology Pty Ltd, we are the most professional spacer manufacturing company. Many different types of style, every kind of specs available. There is noting we cannot produce. State of the art CNC machining, promising very precise results each and everytime. Most importantly, all the machining are done locally in Melbourne, Australia. PCD – 5×114.3 (Car) to 5×120 (Wheel). CB – Custom machine, please provide required bore sizes of car and wheel. Stud Size – M12x1.25 / M12x1.5 / M14x1.25 / M14x1.5 / 1/2″-20 UNF / 7/16″ (Please specify size required). Qty – 2 pcs. Outer Diameter- 155 mm. Lip Height – 10mm. Stud hole diameter 15 mm. Inserted studs length 28mm, unless specified. Spacer nuts will be included as per the photo illustration. Photo is generic but a very close example to finished product. Note- If your car uses lug bolts, you may need spacer bolts to screw these spacers onto your hub. After you placed the order sent us a message in this format. PCD (HUB)5×100 to PCD (Wheel) 5×100. Lug Nuts- M12x1.25 or M12x1.5 or M14x1.25 or M14x1.5 or 1/2-20 UNF. 1910 Bravo Romeo 148. PCD (HUB)5×98 to PCD (Wheel) 5×98. Car CB- 58.1. Wheel CB- 69.1. Lug Bolts- M12x1.25. We will try our best to assist you in finding the relevant information. Please let us know your car brand, model, year, we can provide you related data and information for you to refer to. Depending on the issue, we are open to negotiate and come up with a relatively reasonable solution. You will always have to confirm the spec with us, otherwise we cannot machine anything for you. Unless the description already have fixed detail on the spacer. If you are unsure of any of this information please let us know, we can go deeper into detail with you. Thus if you get 30mm spacer, you definitely don’t have to grind anything for sure. We will supply spacer nuts according to your car’s stud, and insert studs according to your car’s. If your car has M12x1.25 studs. We will provide M12x1.25 Spacer Nuts and M12x1.25 Studs into the spacer. This will allow you to use the factory lug nuts to tighten the wheel down. If your car uses lug bolts (threaded insert into the hub to tighten wheel down), that means you may need spacer bolts to secure the spacer onto your hub. It will be flush if the spacer is 20mm plus. Ref to photo below. Some cases where the wheels have gap in between the stud holes, hex head can perfectly sit in there, but only some cases works. For this set up if you want to use your factory lug bolts to tighten the spacer down, you might end up having the either grind the hex head down to stop any protrusion. ALSO the thread that surpass the hub might come to contact the hand brake mechanism or braking plate, this means the bolts is too long, you will have to grind the excess thread away to stop it from hitting the hand brake mechanism. If you are looking to change the PCD of the car to different PCD you will have to make sure the clearance at the back of the wheel allows you to commit this changes. Sometimes if there is a rebate or recess on the back of the wheel, does not mean there is enough clearance, usually if the stud pattern is changed dramatically eg. 5×100 to 5×120 then there might be an issue. With Stock Bolt, in this wheel there is just enough rebate to allow the hex to sit in it, if there isn’t a rebate you may need to get thicker spacer or grind down the hex head or get low profile hex bolt. Spacer shown is a 15mm spacer. For this specific rim there is a very deep rebate spacing, therefore will definitely have enough clearance for higher bolt. This rim has very shallow rebate (almost no rebate), the hex head will contact the wheel as the shown below, this will be very unsafe for you to use, as the wheel is not contacting the face of the spacer, only the hex head. Driving in this case may result in wheel breaking the stud off, with extreme vibration and tyre wear. Centerbore alignment is very important, and here is how we machine the size of our spacer. If you car has a Centerbore of 56.1mm, our adapter will be made 56.2mm roughly, with. 1mm clearance will allow the spacer to fit on to your hub. 1mm, just tell us the exact measurement. However if your wheel has a Centerbore of 56.1mm, we will make the hub centric lip to be 56.1mm or slightly smaller less than. Simply because normally the wheel CB is slightly larger to allow the wheel to fit. If your Centerbore height is more than the spacer, it means you will either have to go with spacer without hub centric lip or us thicker spacer. As our hub centric spacer need to have taper to allow the change of center bore size. For Example if your Centerbore height is 12mm, you will have to go with 15mm spacer as minimum, if your Centerbore is 15mm tall, you will have to go with 20mm spacer. If your bore does not look anything similar to the photo shown below, send us a photo with as many dimensions included as you can, so we can try to determine how we can go about this. 6061 T6 Aluminium Alloy- T6 temper 6061 has an ultimate tensile strength of at least 290MPa (42,000 psi) and yield strength of at least 250 MPa (35,000 psi). More typical values are 310 MPa (45 ksi) and 270 MPa (39 ksi) respectively. Note: Australia Post is currently experiencing significant delays. At Caold Technology our spacer adapters are made with state-of-the-art CNC machine in Melbourne, Australia, with the highest quality materials (Aluminum 6061-T6). All insert studs and nuts provided are Grade 10.9 steel. All products & services we offer carry corresponding Australian laws & regulations. It is your responsibility, to make sure to use our product correctly. Wheel spacer are legally manufactured and intended for Exhibition Cars only. We accept the return if. The product was wrongly produced. The result of the spacer did not match your required spec. The item have been used, cause scratches in the product. You decided not to use it, or don’t need it (change of mind). You used on non intended application and destroyed our product. You have damaged the product beyond repair. Specs provided was wrong. One Year Manufacturing Guarantee. At Caold technology, we produce reliable products, this is to give you a peace of mind when you use our product. We do not tolerate misuse, misconduct, abusive or improper installation. Guarantee does not apply to vehicle with aftermarket performance enhancement such as suspensions upgrades, any large gain of horse power to the wheels. We do machine spacers/adapters at varies thicknesses such as 15, 20, 25, 30, 35 mm or more. If you have any enquiry, complaints or feedback. We will do our best to satisfy your needs and answers your question at our best ability. All Our spacer adapters are made-to-order or custom made. Therefore we cannot accept any return. Any return items will be customer expense. One Year Manufacturing Guarantee, a t Caold technology, we produce reliable products, this is to give you a peace of mind when you use our product. The item “Wheel Spacer Adapters 15 mm 5×114.3 To 5×120 Conversion Hub Centric 2 PCS” is in sale since Tuesday, November 22, 2016. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Wheels, Tyres\Wheels”. The seller is “caold_technology” and is located in Moorabbin. This item can be shipped worldwide.

• Manufacturer Part Number: CD1312131438
• Brand: Caold Technology
• UPC: Does not apply